Spray foam and blown-in attic insulation built for Florida heat
Roof Insulation Apopka FL is the fastest way to stop your attic from baking your living room. We install spray foam and blown-in insulation for homeowners in Apopka, Florida, and across Orange County. If your ceilings feel warm in July and your AC runs nonstop, you are losing cold air straight through the roof deck. We fix that.
Roof Insulation Apopka FL is the layer of material between your living space and the roof deck that slows heat transfer. In Apopka, that layer has to fight radiant heat, not just cold. We install closed-cell spray foam directly on the roof deck, or blown-in fiberglass and cellulose across the attic floor, depending on your roof type and ventilation. The goal is simple: keep the 90-degree attic air out of your house.
Most homes we inspect in Apopka were built before 2005 with R-19 batts at best, and some have insulation that has been crushed by decades of foot traffic and rodent nesting. When you call us for attic insulation Apopka homeowners get a free thermal read, and we tell you whether you need a full re-insulation or a top-off. If you have been searching for roof insulation Apopka FL near me, this is the work we do every week.
Insulation is not a comfort upgrade. In Central Florida it is the single cheapest way to cut a cooling bill, and it protects the roof structure itself from heat damage.
A properly insulated roof deck can drop attic temperatures by 30 to 40 degrees on a July afternoon. Homeowners in Apopka typically see 15 to 25 percent off summer cooling costs after we finish. You will notice the AC cycling less within the first week.
Florida humidity plus a hot roof deck equals condensation on the underside of your sheathing. That moisture rots rafters and feeds mold. Closed-cell spray foam seals the deck and blocks that moisture path, which is why we recommend it for homes with attic condensation problems.
Heat is the number one killer of asphalt shingles in Orange County. When the attic stays cooler, the shingles above it stay cooler too. Insulation will not add years to a failing roof, but it slows the thermal cycling that curls shingle edges and dries out sealant.
Spray foam roof insulation Apopka FL adds a dense layer between you and the outside. Rain on a metal roof goes from a drum solo to a background hum. If you live near 441 or the 429, the road noise drops noticeably too. It is a side benefit most customers mention after the first storm.
Every job starts with a free attic inspection and ends with a thermal camera walkthrough. Here is exactly what happens from the first call to the final check.
We climb into the attic and measure existing insulation depth, check for moisture, and photograph the roof deck. You get a written report with R-value findings and a flat quote the same day. Most inspections take 30 to 45 minutes.
Before any insulation goes in, we seal the gaps that leak air: top plates, wire penetrations, recessed lights, and the attic hatch. This step takes two to four hours and is the difference between insulation that works and insulation that just sits there.
For spray foam, we apply closed-cell foam directly to the roof deck at 2 to 3 inches, hitting R-14 to R-21. For blown-in, we dense-pack the attic floor to R-38. A typical 1,800 square foot attic takes one day.
We check ridge vent and soffit vents to make sure the attic can still breathe if you chose blown-in. If we find clogged soffits or a failed ridge vent, we clear or replace them before we close out the job.
We walk the attic with a thermal camera and show you the before-and-after temperature readings. You get photos of the finished work and a written summary of the R-value we achieved. Then we clean up and haul off every scrap.
Roof Repair Apopka has been working on Central Florida roofs since 2010. That is 16 years of attics in Orange County heat, and we have insulated everything from 1970s block homes near South Apopka to new builds in the 32712 ZIP. Our installers are trained on GAF and Owens Corning systems, and we follow Florida Building Code energy requirements on every job. We are not insulation-only contractors. We understand how the roof, the deck, and the attic work together, which means we catch problems an insulation-only crew would miss.
We are a roofing company that insulates, not an insulation company guessing at roofs. That matters when the deck is soft, the vents are wrong, or the last crew left a mess.
If we open your attic and find a roof leak or flashing failure soaking the deck, we stop and show you. We repair it before insulating, because spraying foam over wet sheathing traps the problem. Most insulation-only companies walk away from that.
You get one number before we start. No per-bag charges, no surprise attic fee, no charge for the inspection. If the scope changes because we find damage, you approve it first. That is how we have kept a 4.9-star average across 16 years.
Our roof insulation service Apopka homeowners get is spec'd for radiant heat, not northern winters. We use closed-cell foam on the deck because it handles the 140-degree attic temps that blow-in alone cannot stop. That is the difference you feel in August.
From South Apopka FL to Plymouth and Zellwood, we run insulation crews across Orange County six days a week. If you are in 32703 or 32768, we can usually inspect within 48 hours. Call 545-637-623 and we will get you on the schedule.
Every job includes the inspection, the air sealing, the insulation itself, and the final thermal check. Here is what is covered in a standard quote, and what we treat as an add-on if we find it.
We measure existing insulation depth, check for moisture and rodent damage, and photograph the roof deck. You get a written report and a flat quote the same day, no charge for the visit.
We seal top plates, wire penetrations, recessed light cans, and the attic hatch with foam and caulk. This step is included on every job because insulation alone does not stop air movement.
Applied directly to the roof deck at 2 to 3 inches for R-14 to R-21. This is our standard recommendation for Apopka homes with attic condensation, metal roofs, or tile roofs that run hot.
Dense-packed fiberglass or cellulose installed to R-38 across the attic floor. This is the budget-friendly option when your deck is sound and your ventilation is already balanced.
We verify ridge vent and soffit vents are open and working. If soffits are clogged or a ridge vent has failed, we clear or replace it before we finish the job.
We walk the attic with a thermal camera and show you the before-and-after temperature readings. You get photos of the finished work and the R-value we achieved in writing.
Most attic problems in Apopka come down to heat, moisture, or both. Here is what we run into every week and how we fix it.
Your AC runs nonstop from May through October and never gets ahead of the load. Ceilings stay warm to the touch and bedrooms never cool down at night.
We install closed-cell spray foam on the roof deck to block radiant heat before it enters the attic. Attic temps drop 30 to 40 degrees, and your AC starts cycling normally again within the first week.
Moisture condenses on the underside of the roof deck and drips onto insulation, which kills its R-value and feeds mold on rafters and sheathing.
Closed-cell foam seals the deck and blocks the moisture path entirely. We also check ventilation and fix any soffit damage or clogged vents feeding the problem.
Decades of foot traffic, rodents, and roof repairs flatten batts to nothing. You are paying to cool an attic that has almost no thermal barrier left.
We remove the failed material, air-seal the attic, and install new insulation to R-38 or deck foam to R-21. You get a thermal report showing the R-value we achieved.
A skylight leak, chimney leak, or flashing failure soaks the insulation. Wet insulation loses most of its R-value and grows mold fast in Florida humidity.
We trace and repair the leak first, then remove and replace the wet insulation. We never insulate over a leak, because foam over wet wood traps the problem permanently.
We inspect, air-seal, and either blow in R-38 on the floor or spray the deck depending on your ventilation. Most of these homes get deck foam because the old vents are undersized.
Cooling bills drop 15 to 25 percent, and the house holds temperature through the afternoon instead of cooking from 2 to 6 PM.
Metal roofing panels radiate heat straight into the attic. We spray closed-cell foam on the deck to stop that transfer, and we check the ridge vent while we are up there.
Attic temps fall by 30 to 40 degrees, and the back bedrooms finally cool down with the rest of the house.
We install ice and water shield and closed-cell foam before the new shingles go down. Bundling with roof replacement saves a second mobilization and a second crew.
You get a new roof and a code-compliant insulation package in one project, with no extra trip charge.
Adding blown-in over a wet deck makes condensation worse. We diagnose the moisture source, seal the deck with closed-cell foam, and balance ventilation.
The dripping stops, the mold risk goes away, and the insulation you paid for actually performs.
We use it to find hot spots, air leaks, and moisture before we insulate, and again after to prove the temperature drop. You see the before-and-after readings yourself.
Proportioner and heated hose setup that mixes and applies foam at the correct ratio. Off-ratio foam does not cure right, so we run calibrated equipment on every job.
Dense-packs fiberglass or cellulose to a consistent R-38 across the attic floor. We adjust the feed rate so the depth is even, not piled in one corner.
Checks sheathing and rafter moisture before we insulate. If the reading says wet, we stop and fix the leak source first.
Caulking gun, foam sealant, and backer materials for top plates, wire penetrations, and recessed lights. This step is what makes the insulation work.
We work on roofs and in tight attic spaces. Harness, stabilizer, and OSHA-compliant fall protection keep the crew safe and the job insured.
We clear loose debris, old insulation dust, and roof algae buildup before installing new material, then clean the attic and the driveway before we leave.
We apply 2 to 3 inches of closed-cell foam directly to the roof deck, which seals air and moisture at the same time. This is our standard method for Apopka homes with condensation, metal roofs, or tile roofs. It hits R-14 to R-21 at the deck and performs like a much higher R-value because it stops air movement.
When the deck is sound and ventilation is balanced, we dense-pack fiberglass or cellulose across the attic floor to R-38. This is the budget path, and it works well in homes with working ridge vent and soffit vents. We verify vent flow before we install.
We seal top plates, wire holes, recessed lights, and the attic hatch before any insulation goes in. Skipping this step is the most common reason insulation underperforms, and it is included on every job we run.
Every job is spec'd to Florida Building Code energy requirements for our climate zone. We document the R-value achieved and the materials used, which matters if you sell the home or file an insurance claim.
We walk the attic with a thermal camera after installation and record the temperature drop. You get the readings and photos, so you have proof the work performed as quoted.
Apopka sits in Orange County, and our attic conditions are different from what you would see in North Florida. Summer attic temps hit 140 to 160 degrees on a sunny afternoon, and the humidity stays high enough that condensation is a real risk on the underside of the roof deck. Most of the housing stock here was built between 1970 and 2005, which means original R-11 or R-19 batts that have been crushed flat by decades of foot traffic and rodent nesting. Florida Building Code calls for R-38 in the attic floor for our climate zone, and most older Apopka homes are nowhere close. We also see a lot of tile roofs and metal roofing panels, both of which run hotter than shingles and benefit most from deck-level closed-cell foam. If you are looking for roof insulation South Apopka FL or anywhere in the 32712 and 32703 ZIP codes, we can usually inspect within 48 hours. The cost of roof insulation in Apopka Florida depends on attic size and material, but the payback is fast here because our cooling season runs seven months.
Older block homes with original R-11 batts and undersized soffit vents. Deck foam is usually the right call here because the existing ventilation cannot support blown-in.
Larger homes with tile roofs and cathedral ceilings. These attics run hot and often have condensation issues that deck foam solves in one visit.
Mix of older frame homes and newer builds. We see a lot of crushed batts from past roof repairs and rodent damage in the older homes.
Rural properties with outbuildings and metal roofs. Corrugated metal and standing seam metal both need deck foam to stop condensation on the panels.
Dense housing stock from the 1960s and 70s. Most attics here need full re-insulation, not a top-off, because the original material is gone.
Radiant heat drives straight through batts and into your living space. Closed-cell foam on the deck blocks that transfer, which is why we recommend it over blown-in for most Apopka homes.
Moisture condenses on the underside of the roof deck and drips into insulation. Sealing the deck with foam stops the condensation path entirely.
Original R-11 and R-19 insulation in 1970s and 80s homes is usually flat and useless. We remove it, air-seal, and install new material to current code.
Storms tear shingles and open the roof, which soaks insulation. We repair the roof first, then replace any insulation that lost its R-value to water.
Original R-11 batts crushed to less than an inch in most of the attic. Summer power bills averaged $287, and the back bedrooms never dropped below 78 degrees even with the AC running all day.
We air-sealed the attic and sprayed 3 inches of closed-cell foam on the deck, hitting R-21. Attic temp dropped from 152 to 108 degrees. The next July bill came in at $214, and the back bedrooms now hold 74 degrees.
We recommend an annual attic check to verify foam is intact and vents are clear. Foam does not settle or compress, so it holds its R-value for the life of the roof.
Condensation dripped from the attic hatch every summer, and the homeowner had already paid one company to add blown-in insulation. The added material made it worse by trapping moisture against the deck.
We removed the wet blown-in, sealed the deck with closed-cell foam, and balanced the soffit vents. No drips in two summers since, and the attic humidity reading dropped from 78 percent to 54 percent.
Keep soffit vents clear of debris and check the attic hatch seal each spring. We inspect the foam on our annual maintenance visits at no extra charge.
Standing seam metal roof with no deck insulation. Attic temps hit 158 degrees in August, and the homeowner described the back of the house as unlivable from 2 to 6 PM. Cooling bill averaged $310 in summer.
We sprayed 3 inches of closed-cell foam on the deck and sealed the ridge. Attic temp dropped to 112 degrees, and the summer bill fell to $238. The homeowner says the whole house now cools evenly.
Metal roofs expand and contract, so we check the foam bond at the panel seams once a year. No other maintenance is needed for the insulation itself.
Most attic insulation jobs in Apopka run $1,800 to $4,500 in 2026, depending on square footage and material. Blown-in fiberglass for a 1,500 square foot attic starts around $1,800. Closed-cell spray foam on the roof deck typically runs $3,000 to $4,500. We give you a flat quote after the free inspection, so the number you hear is the number you pay.
Florida Building Code calls for R-38 in the attic floor for our climate zone, and we hit that with blown-in every time. If we are spraying the roof deck with closed-cell foam, 3 inches gets you R-21 at the deck, which performs like a much higher R-value because it also seals air. For most Apopka homes, R-38 attic floor or R-21 deck foam is the right target.
We do. Roof Repair Apopka has been installing roof insulation in Apopka and Orange County since 2010. We are a licensed Florida roofing contractor, which means we can also fix the deck, flashing, or ventilation problems we find while we are up there. Call 545-637-623 or request the free attic inspection online and we will get you scheduled.
Yes, and the drop is measurable. Apopka homeowners typically see 15 to 25 percent off summer cooling costs after we insulate, because the attic stops transferring heat into the living space. On a $250 monthly summer bill, that is $37 to $62 back in your pocket every month. Most customers break even on the insulation cost in two to four summers.
They insulated our attic in South Apopka and caught a chimney flashing leak we did not know about. Fixed both in one day. Power bill dropped $73 the first full month. Straight answers, flat price, no upsell.
We had condensation dripping from the attic hatch for two summers. Roof Repair Apopka explained why blown-in would make it worse and sprayed the deck instead. No drips since. They showed us thermal photos before and after.
Insulated six rental homes for me across Apopka and Ocoee. Flat pricing on each, photos of every finished job, and tenants stopped calling about the AC. Professional crew, cleaned up after themselves.
Metal roof made the back bedrooms unbearable. They sprayed foam on the deck and the difference is night and day. Attic went from 158 to 112 degrees. Worth every dollar.
If your roof is at the end of its life, we install new GAF or Owens Corning systems and insulate the deck at the same time. Bundling saves you a second crew and a second mobilization fee.
Roof InstallationA full replacement is the best time to upgrade insulation, because the deck is open. We install ice and water shield, then closed-cell foam before the new shingles go down in Apopka.
Roof ReplacementInsulation traps moisture, so we never insulate over a leak. If we find roof leaks, flashing failure, or soft sheathing during inspection, we repair it first and then insulate.
Roof RepairEvery insulation job starts with an inspection. We check the deck, ventilation, and existing R-value, then give you a written report with photos and a flat quote.
Roof InspectionAnnual maintenance keeps vents clear and flashing tight, which protects the insulation you just paid for. We check attic moisture and vent flow on every maintenance visit.
Roof MaintenanceA storm that opens your roof also soaks your insulation. We handle emergency repairs first, then replace any insulation that got wet and lost its R-value.
Emergency Roof RepairWhen a storm tears shingles off, we tarp the roof fast to keep rain out of your attic. Wet insulation has to be removed and replaced, so stopping water early saves money.
Emergency TarpingWe trace roof leaks to the source with moisture meters and thermal imaging. Finding the leak before we insulate is non-negotiable, because foam over wet wood fails.
Leak Detection and RepairAfter a Central Florida storm, we repair wind damage and hail damage, then check whether your attic insulation was compromised by water intrusion.
Storm Damage Roof RepairHail bruises shingles and can crack ridge vents. We repair the damage and verify your attic ventilation still works before we touch the insulation.
Hail Damage Roof RepairA reflective roof coating drops surface temperature and takes load off your insulation. On flat roofs, coating plus insulation is the cheapest cooling upgrade you can make.
Roof CoatingMost Apopka homes have asphalt shingles or architectural shingles. We insulate under both, and we know how each shingle type handles attic heat.
Asphalt Shingle RoofingClay tiles and concrete tiles run hotter than shingles. Tile roofs benefit most from deck-level spray foam, because the tile itself holds heat for hours after sunset.
Tile RoofingMetal roofing panels and standing seam metal radiate heat straight into the attic. Spray foam on the deck is the standard fix for metal roofs in Orange County.
Metal RoofingCorrugated metal is common on older Apopka outbuildings and porches. We insulate these roofs with closed-cell foam to stop condensation on the underside of the panels.
Corrugated Metal RoofingFlat roofs need insulation that handles ponding and heat. We install rigid board or spray foam under TPO and modified bitumen systems to hit code R-value.
Flat RoofingTPO membrane reflects sunlight, but the attic below still heats up. We pair TPO installation with rigid insulation board so the whole assembly performs.
TPO RoofingEPDM membrane is common on Apopka commercial buildings. We add insulation board under the membrane to cut cooling load and meet Florida energy code.
EPDM RoofingPVC membrane handles chemical exposure and heat well. We insulate under PVC on commercial roofs where cooling costs are the biggest line item.
PVC RoofingModified bitumen is a workhorse on low-slope roofs. We install insulation board under it to stop heat transfer into the building below.
Modified Bitumen RoofingCommercial buildings in Apopka lose money through under-insulated roofs. We spec insulation to Florida Building Code and install it during re-roofs to avoid disruption.
Commercial RoofingProper drainage keeps water away from your foundation and out of your attic. We install downspouts that move storm water off the roof fast.
Downspout InstallationClogged downspouts back water up under your shingles and into the attic. We clear and repair them so your insulation stays dry.
Downspout RepairSoffit vents feed your attic ventilation. When fascia rot or soffit damage blocks them, insulation cannot perform. We repair both before insulating.
Fascia and Soffit RepairRidge vent and soffit vents work as a pair. We balance them so your attic breathes, which is required if you choose blown-in insulation over spray foam.
Roof VentilationSkylight leaks soak insulation fast. We repair or replace the skylight and its flashing, then replace any insulation that got wet.
Skylight Installation and RepairChimney leaks are a top cause of wet attic insulation. We repair the flashing and seal the chase before we insulate around it.
Chimney Flashing RepairAttic insulation is the floor-level version of this service. If your roof deck is sound and you have good ventilation, blown-in attic insulation is the cheaper path.
Attic InsulationRoof algae and debris hold moisture against the roof. We clean the roof so it sheds water properly, which protects the insulation underneath.
Roof CleaningReal experiences from customers who chose our Roof Insulation services
Our 1978 block home had R-11 batts that were flat as cardboard. The crew air-sealed the attic, sprayed 3 inches of foam on the deck, and showed me thermal photos before and after. My July power bill dropped from $287 to $214. They also caught a chimney flashing leak I did not know about and fixed it the same day.
Homeowner, South Apopka
We had condensation dripping from the attic hatch every summer. Two other companies wanted to just add blown-in and call it done. Roof Repair Apopka explained why that would trap moisture and recommended deck foam instead. No drips since, and the house holds temperature way better at night.
Homeowner, Wekiwa Springs
I manage six rental homes around Apopka and Ocoee. They insulated all six attics over three weeks, gave me flat pricing on each, and sent photos of every finished job. Tenants stopped calling about AC running all night. That alone paid for the work.
Property Manager, Ocoee
Our 1978 block home had R-11 batts that were flat as cardboard. The crew air-sealed the attic, sprayed 3 inches of foam on the deck, and showed me thermal photos before and after. My July power bill dropped from $287 to $214. They also caught a chimney flashing leak I did not know about and fixed it the same day.
Homeowner, South Apopka
We had condensation dripping from the attic hatch every summer. Two other companies wanted to just add blown-in and call it done. Roof Repair Apopka explained why that would trap moisture and recommended deck foam instead. No drips since, and the house holds temperature way better at night.
Homeowner, Wekiwa Springs
We inspect your attic free, measure your existing R-value, and hand you a flat quote the same day. Licensed Florida roofing contractor, 16 years in Orange County, and a 4.9-star average. Call now and we will get you on the schedule this week.